Deh-p88rs-2 manual

You can switch between modes as desired. Refer to Switching the DSP setting mode on page 9. The 3-way network mode NW lets you cre- ate a 3-way multi-amp, multi-speaker sys HPF 1, F. HPF 2 5 Setting the high pass filter for rear speakers R. HPF 1, R. HPF 1 front high pass filter slope —F. HPF 2 front high pass filter cut-off frequency —R. HPF 1 rear high pass fil- ter slope —R. Page Using The Position Selector Audio Adjustments Using the position selector One way to assure a more natural sound is to clearly position the stereo image, putting you right in the center of the sound field.

Initial is the factory supplied time align- ment. Custom is an adjusted time alignment that you can create for yourself. Please set Auto TA appears. Page Adjustable Parameters Audio Adjustments You can then make precise adjustments to the reproduced frequency band with a low-pass filter or high-pass filter , level, phase and other parameters to match the characteristics of each speaker unit.

Adjustable parameters The network function enables adjustment of the following parameters. If you set a small absolute value for the slope for a gentle slope , interference be- tween adjacent speaker units can easily re- sult in degraded frequency response. If you set a large absolute value for the slope for a steep slope , continuity of sound between speaker units is degraded, and sounds appear to be separated. Adjusting subwoofer settings When the subwoofer output is on, you can ad- just the cut-off frequency and the output level of the subwoofer.

Even if the speaker unit filter is muted, you can adjust the muted speaker units fil- ters. However, mute is automatically can- celed when the level is adjusted. HPF 1 or R. HPF 1. HPF 1 appears in the display.

Page Using Bbe Sound Section Audio Adjustments Using BBE sound With BBE, playback very close to the original sound can be obtained by correction with a combination of phase compensation and high-range boost for the delay of the high-fre- quency components and the amplitude devia- tion occurring during playback.

Page Recalling Equalizer Curves Audio Adjustments Recalling equalizer curves The equalizer lets you adjust the equalization to match car interior acoustic characteristics as desired. There are seven stored equalizer curves which you can easily recall at any time.

Here is a list of the equalizer curves: Display Equalizer curve Powerful When this unit is connected to a power amp with input level control, auto TA and EQ may not be possible if you lower power amp input level. Page 69 Audio Adjustments Select the position for the seat on which the microphone is placed. Page Initial Settings Section Initial Settings Adjusting initial settings 1 1 1 Using the initial settings, you can customize various system settings to achieve optimal per- formance from this unit.

Page Switching The Warning Tone Section Initial Settings Switching the warning tone If the front panel is not detached from the head unit within four seconds of turning off the ignition, a warning tone will sound. You can turn off the warning tone.

Page Correcting Distorted Sound Initial Settings Correcting distorted sound When listening to a CD or other source on which the recording level is high, setting the equalizer curve level to high may result in dis- tortion. You can switch the digital attenuator to low to reduce distortion. Sound quality is better at the high setting so this setting is usually used. ON appears in the display. Switching the feature demo The feature demo automatically starts when power to this unit is turned off while the igni- tion switch is set to ACC or ON.

Press key 3 to close focus, the display should read "91". Press key 2 to implement the tracking balance adjustment the display should now read "81". Press key 3. The display will change, returning to "81" on the fourth press. Refer to the photographs supplied to determine the phase angle. The angle specified above indicates the average angle. This arrangement is intended at reducing nonsense calls from the users and also for facilitating trouble analysis and repair work in servicing.

DTNO remains in blank as before. Focusing not available. Sub-code is strange not readable. A disc not containing CD-R data is found. CD signal error. AGC protection doesn't work. Focus can be easily lost. Remarks: Mechanical errors are not displayed because a CD is turned off in these errors.

Unreadable TOC does not constitute an error. An intended operation continues in this case. Upper digits of an error code are subdivided as shown below: E 1x: Setup relevant errors, 3x: Search relevant errors, Ax: Other errors. The clock signal is output from the PCL1 terminal Pin The frequency of the clock signal is The clock signal should be If the clock signal is out of the range, the X'tal X should be replaced with new one. Remove the two screws and then remove the Case.

Hold the Upper and Lower Frames. Do not hold the front portion of the Upper Frame, because it is not very solid. A B Do not squeeze this area.

With a disc inserted and clamped in the mechanism, remove the two Springs A , the six Springs B , and the four Screws. Turn the Upper Frame using the part "a" as a pivot, and remove the Upper Frame. While lifting the Carriage Mechanism, remove it from the three Dampers.

Caution: When assembling, be sure to apply some alcohol to the Dampers and assemble the mechanism in a clamped state. Apply Shorting Solder to the flexible cable of the Pickup, and disconnect it from the connector. Unsolder the four leads, and loosen the Screw. Remove the CD Core Unit. Make the system in the carriage mechanism mode, and have it clamped. While releasing from the hook of the Inner Holder, lift the end of the Feed Screw.

Assemble the sub unit side of the Pickup, taking the plate Chassis in-between. When connecting tweeters, please confirm the.

When you set. Pioneer VSXS. Renombrar el marcador. Eliminar marcador? Eliminar de mis manuales? Entrar O. Cargar el manual.

Cargar desde el disco. Soldering should be finished with the proper quantity. Refer to the example. Please be sure that all screws are fastened, and that there are no loose screws.

Please be sure that all connectors are inserted, and that there are no imperfect insertion. Please replace the wiring and cables to the original state after repairs. In addition, be sure that there are no pinched wires, etc. Please check that neither solder debris nor screws remain inside the product. Damaged power cords may lead to fire accidents, so please be sure that there are no damages. If you find a damaged power cord, please exchange it with a suitable one.

When spark traces or similar marks are found on the power supply plug, please check the connection and advise on secure. Please exchange the power cord if necessary.

When you perform repairs, please pay attention to static electricity, furniture, household articles, etc. Please pay attention to your surroundings and repair safely. To keep the original performance of the products, optimum adjustments and confirmation of characteristics within specification. For parts that require cleaning, such as optical pickups, tape deck heads, lenses and mirrors used in projection monitors, proper.

Lubricants, Glues, and Replacement parts. Use grease and adhesives that are equal to the specified substance.